Sketch Picture¶
Inserts an image on the sketch plane to trace over, scaled from two points a known distance apart.
Sketch tab > Sketch Picture, or Sketch Picture… in the Pictures section of the sketch's property panel. To paste an image from the clipboard, press Ctrl+V in the sketch, or right-click in the graphics area > Paste Picture. A sketch must be open.

Inserting a Picture¶
- Open a sketch.
- Click Sketch Picture and select an image file (PNG, JPEG, BMP, GIF or WebP), or copy an image and press Ctrl+V.
- The picture is placed at the center of the view, 60% of the view's width, and its page opens.
- Move, scale and rotate it, in the graphics area or on the page.
- Click OK or press Enter.
Pasting takes PNG data (as copied from a browser, Office or the Snipping Tool), an image file copied in Explorer, or a plain bitmap, which is kept as a PNG. Photos are turned upright from the orientation the camera recorded.
Everything done on the page is one undo step. Cancel or Esc puts the picture back as it was, and removes a picture just inserted.
Scaling to a Known Distance¶
- On the picture's page, under Scale From Two Points, click Place Points.
- Click two points on the picture whose distance apart you know, such as the ends of a dimensioned feature.
- Enter the Distance between them.
- Click Apply Scale.
The picture scales about the first point, which stays where it is. Press Esc while placing the points to stop.

Removing a Background¶
- Under Background, turn on Remove background. The color most of the picture's border is becomes the background color.
- To use another color, click Select Color, then click that color on the picture.
- Raise the Tolerance until the background is gone. Turn on Only where connected to the border to keep areas of the same color inside the part.

Moving, Scaling and Rotating in the Graphics Area¶
While the picture's page is open:
| Drag | Result |
|---|---|
| Inside the picture | Moves it |
| A corner handle | Scales it about the opposite corner, its aspect ratio kept |
| The round handle above it | Rotates it about its center. Within 1° of a multiple of 90° it snaps to it |
The page's values update when you release the mouse button.

Picture¶
Shows the image's file name and its size in pixels.
Position¶
- X
- The picture's center along the sketch's X axis, in the part's units.
- Y
- The picture's center along the sketch's Y axis.
- Angle
- The picture's rotation about its center, counterclockwise from the sketch's X axis.
Size¶
- Width
- The picture's width along its own axis, in the part's units.
- Height
- The picture's height along its own axis.
- Lock aspect ratio
- Changing Width or Height changes the other in proportion. On by default.
- Original Aspect Ratio
- Sets Height from Width to the image's own proportions in pixels.
Scale From Two Points¶
- Place Points
- Starts placing the two points on the picture. Shows Placing Points… until both are placed.
- Separate X and Y distances
- Sets the scale separately along the picture's own width and height, for an image stretched in one direction.
- Distance
- The distance between the two points. With Separate X and Y distances on, enter X distance and Y distance instead: the points' distance apart along the picture's width and along its height. Each needs the points to be far enough apart in its direction.
- Apply Scale
- Scales the picture so the points are the distance apart. The first point stays where it is on the sketch.
- Make Horizontal, Make Vertical
- Rotate the picture about the first point so the line between the points is horizontal or vertical, by the smaller turn. Use them to straighten a photo taken at an angle.
- Place Points Again
- Clears the points and starts placing them again.
Background¶
- Remove background
- Makes the background color transparent.
- Color
- The background color removed, from the border at first. Select Color takes it from a point clicked on the picture.
- Tolerance
- How far a color can be from the background color and still be removed, from 0 to 100%. Default 15%. Colors just past it fade out, so the edge is not jagged.
- Only where connected to the border
- Removes only background reached from the picture's border without crossing other colors.
Edges¶
Finds the edges in the image, to trace a photo's outlines.
- Show
-
Option Shows Picture The picture only Edges over picture The edges in orange over the picture Edges only The edges alone, in dark blue - Sensitivity
- How many edges are found, from 0 to 100%. Higher sensitivity finds fainter edges. Default 50%.
Edges are found on the picture before its background is removed.

Display¶
- Opacity
- From 0 (invisible) to 100% (opaque).
- Delete Picture
- Removes the picture from the sketch and closes the page.
Pictures on the Sketch Page¶
The sketch's property panel lists its pictures under Pictures:
- The checkbox shows or hides the picture. A hidden picture is shown again while you edit it.
- Edit opens the picture's page. You can also double-click the picture in the graphics area with the Select tool, off any sketch entity.
- The delete button removes it.
Pictures are drawn under the sketch geometry. A sketch shown in the graphics area outside sketch edit shows its pictures too: on its plane, behind the model where the model is in front, and over the model while the view is normal to the plane. To trace over a picture in an earlier sketch, show that sketch and press N with it selected (in a sketch on the same plane, N alone), so the solids built from it do not hide the picture.
How Pictures Are Stored¶
The image is embedded in the part file, so the part does not depend on the original file. The same image inserted more than once is stored once. Background removal and edges are display settings: the original image is kept and processed again when they change.