Drafting Standard¶
Sets the standard a drawing is drawn to, and the units, decimals, arrows, text height and spacing every dimension and annotation in it uses. The settings are saved with the drawing.
Drawing tab > Drafting Standard, or right-click the drawing's row at the top of the design tree > Drafting Standard…. The Options window opens on the drawing's Document Properties tab, at the Drafting Standard page. Tools > Options > Document Properties opens the same pages.
img/drawings/drafting-standard-dialog.png
The Options window on a drawing's Document Properties tab, the Drafting Standard page shown, the four drawing pages listed on the left.
Changing the Standard¶
- Click Drafting Standard.
- Set Drafting standard, and change any setting on the other pages.
- Click OK.
The sheet updates at once. Changing the document properties is one undo step. A setting made on a dimension or note itself, such as its decimals or text height, is kept.
A new drawing takes its standard from its sheet format: ASME for a format that numbers its zones from the lower right, ISO for any other.
Drafting Standard¶
- Drafting standard
-
ISO (ISO 129) or ASME (Y14.5). Sets the text height, the dimension text direction and the leading zeros wherever the other pages leave them to the standard:
ISO ASME Text height 3.5 mm 3 mm Dimension text Aligned, read from the bottom or right Unidirectional, read from the bottom Leading zeros Shown Left off in inches ( .5)
Units¶
- Units
- MMGS (millimeter, gram, second) or IPS (inch, pound, second), for dimensions and title block values. A new drawing takes its units from its sheet format. Changing them changes this drawing only.
- Lengths
- Decimal places of length dimensions: As needed or 0 to 5. As needed gives up to 4 places in millimeters and 5 in inches, without trailing zeros.
- Angles
- Decimal places of angle dimensions: As needed (up to 2 places) or 0 to 5.
- Show lengths in the other units too
- Adds each length in the other unit system, in brackets after the value:
25.4 [1.000]. - Dual unit decimals
- Decimal places of the value in brackets, 0 to 5. Default 3.
Dimensions¶
- Leading zeros
- The zero before the decimal point,
0.5or.5: Per standard (left off for ASME in inches), Show or Remove. - Trailing zeros
- The zeros that pad a value to its set decimals,
2.50or2.5: Per standard (shown), Show or Remove. A value with decimals As needed has none. - Tolerance decimals
- Decimal places of tolerances: Same as value or 0 to 5.
- 45° chamfers
- How a chamfer dimension writes a 45° chamfer: 2 X 45° (ASME), 2 × 45° (ISO) or C2 (ISO 129-1). Chamfers at other angles get a length and an angle.
- Style
- The arrowheads: Filled, Open, Dot or Architectural tick.
- Length, Width
- The arrowhead's size on paper, in the drawing's units. Default 3 mm by 1 mm.
- Gap
- The distance between an extension line and the geometry it measures. Default 1 mm.
- Extension
- How far an extension line runs past the dimension line. Default 2 mm.
- Between dimensions
- The distance between rows of dimensions, and from the view to the first row. Auto Arrange uses it, and dragged dimensions snap to it. Default 10 mm. See Dimensions.
Sizes are entered in the drawing's units. A size typed with a unit, such as 3mm, is read as written.
Annotations¶
- Height
- The text height of dimensions and annotations on paper. Leave it empty for the standard's: 3.5 mm for ISO, 3 mm for ASME. A height set on an annotation itself is kept.
- Dimension text
- Per standard, Aligned: read from the bottom or right (ISO) or Unidirectional: read from the bottom (ASME).
- Landing
- The length of the short horizontal segment of a leader at its text. Default 3 mm.
Line Weights¶
Drawing tab > Line Weights switches how lines are drawn on screen. Off, every line is one or two pixels wide at any zoom, for editing. On, lines are as wide as they print, so the sheet looks as the PDF will. Exports and printouts always use the printed widths.
img/drawings/drafting-standard-line-weights.png
The same view with Line Weights off and on, visible edges heavy and dimensions thin when on.