Model View¶
Adds a view of a part or assembly to the sheet, seen from a standard direction, or lays out its three standard views and an isometric view.
View Layout tab > Model > Model View. A new drawing opens the page at once.
img/drawings/model-view-page.png
The Model View page with a part selected under Model and the Front tile chosen under Orientation.
Adding a Model View¶
- Under Model, select the part or assembly, or click Browse… to add one from a file.
- Under Orientation, click the view to add. Double-click a tile to add it at once.
- Click OK.
- The view follows the pointer. Click where it goes on the sheet. Esc cancels it.
The view takes the sheet's scale. Once placed, it is selected: drag it into place, or right-click it > Projected View to add the views projected from it (see Projected View).
With Standard 3 View chosen, OK lays out the views at once instead (see below).
Model¶
The models the drawing shows, then the parts and assemblies open in tabs that have been saved. The first one is selected when the page opens.
- Browse…
- Adds a part or assembly file to the list and selects it. The model is added to the drawing with its view; canceling the view leaves it out again.
Orientation¶
One tile for each view, drawn from the model once the drawing has it loaded:
| Tile | Adds |
|---|---|
| Standard 3 View | The front, top, right and isometric views, laid out to fit the sheet |
| Front, Back, Top, Bottom, Right, Left | The model seen from that side |
| Isometric, Trimetric, Dimetric | A pictorial view of the model |
Click a tile to choose it, or double-click it to choose it and click OK in one step. Standard 3 View is chosen when the page opens.
Standard 3 View¶
View Layout tab > Model > Standard 3 View, or right-click the sheet away from the views > Standard 3 View.
Lays out the front view with the top view and the right view projected from it, and an isometric view in the corner they leave:
| Projection angle | Top view | Right view |
|---|---|---|
| Third angle | Above the front view | To the right of the front view |
| First angle | Below the front view | To the left of the front view |
The sheet's scale is set to the largest standard scale at which the views fit inside the border, above the title block. The top and right views are projected views: they stay in line with the front view and follow its display style (see Projected View).
The command shows the model of the sheet's first view, or the drawing's first model when the sheet has no views. If the sheet has views, it asks first, as it replaces them: click Replace Views. From the Model View page, the Standard 3 View tile adds the views of the model selected there without removing the views already on the sheet.
img/drawings/model-view-standard3.png
A sheet laid out by Standard 3 View: front, top, right and isometric views of a part.
Other Ways to Add a View¶
- Right-click the sheet
- Right-click the sheet away from the views > Model View > a direction: a view of the model of the sheet's first view, where you right-clicked.
- Drag a file onto the sheet
- Drag a part or assembly from the Open Parts list or from the file explorer onto the sheet. On an empty sheet the first one is laid out as its standard views, as Standard 3 View does. Otherwise each one comes in as a front view where it is dropped.
- View Palette
- While a drawing is the active document, the View Palette task pane shows a model's views as tiles. Select the model at the top, or click the open button beside it to add a file. Drag a tile onto the sheet to add that view where it is dropped. With Projected views after a drop selected (the default), dropping a front, back, top, bottom, right or left view starts placing projected views from it: click beside, above or below it for each one, and press Esc when done. The refresh button draws the tiles again from the model.
img/drawings/model-view-palette.png
The View Palette task pane beside a drawing, with a part's view tiles and Projected views after a drop selected.