Skip to content

Fillet

Rounds the selected edges or faces with a constant radius.

Features tab > Fillet, or right-click an edge > Fillet.

The Fillet page beside a part with filleted edges: Edges and Radius under Items To Fillet, Scope and Options closed.

Creating a Fillet

  1. Select edges or faces in the graphics area. You can also select them after the page opens.
  2. Click Fillet.
  3. Type the Radius. The field has the focus when the page opens and gets it back, with its text selected, after each selection in the graphics area. The preview updates as you type.
  4. Click OK or press Enter.

A selected face adds all of its edges. Selecting an item already in the list removes it.

Items To Fillet

Edges
The edges, or faces whose edges, to fillet. Select a row and press Del to remove it.
Radius
The fillet radius, in the part's units. Accepts an equation or a variable name.

Scope

Fillets edges found on the body instead of, or in addition to, the edges selected. Use it for the many blends of a casting or molded part in one feature.

Scope

Which edges are filleted besides the ones selected:

Option Edges
Selected edges Only the edges in Items To Fillet (default)
Whole body Every edge of the body of the type set in Edges
Features The edges of the selected features of the type set in Edges

Choosing Whole body or Features shows Edges, Exclude and a note; Features also shows the features list. The features stay in the list while another scope is chosen.

Edges

Which edges the scope takes:

Option Edges
Concave Inside corners
Convex Outside corners
Concave and convex Every corner

One cast part filleted with Whole body and Edges set to Concave, Convex, and Concave and convex.

Features
With Scope set to Features: the features whose edges to fillet, including their pattern and mirror copies. With one feature, the scope takes its own edges and the edges where it meets the body: a boss's top and side edges and its foot. With several, it takes the edges where any two of them meet and the edges within each one, but not where they meet the rest of the body. Select the features in the design tree or the graphics area.
Exclude
Edges the scope leaves sharp. Select them in the graphics area.

Edges in the scope that cannot be filleted are skipped, and the feature shows a warning. Add them to Exclude to leave them out without the warning.

Options

A folding section: click its title to open or close it. It is closed when the page opens unless one of its options differs from its default.

Tangent propagation
Also fillets edges tangent-connected to the selected ones. On by default.
Overflow: trim at neighboring faces
Where the fillet runs into neighboring geometry, it is trimmed by that geometry instead of failing. On by default.
Fade length

Where the fillet wraps around another fillet and runs on into an edge that is not selected, such as the foot of a boss around its side fillet, it fades out to nothing at that fillet's tangent point. This sets how far back from that point the fade starts.

Value Result
Empty (Whole wrap) Fades over the whole wrap
0 Ends square
A length Fades over that length

A boss's foot fillet wrapping around its side fillet, with Fade length empty, 0 and a short length.

Mixed corners

Where convex and concave edges meet at a corner, which is filleted first. The other then rolls around it.

Option Result
Auto Convex first where as many of each meet, otherwise the type with fewer edges first
Convex first (blended foot) The foot wraps around the side's fillet and fades out
Concave first (continuous foot) The side's fillet runs down onto the foot's, forming one continuous foot

A boss corner where convex and concave edges meet, filleted Convex first and Concave first.

Round corners
Where straight fillets between flat faces turn round a sharp corner of what stands on the face they run along, such as a rib's or a pedestal's corner, the ball rolls round that corner, giving a rounded corner that leans out slightly over the corner's faces. Off, the default: each fillet runs on past the corner and is cut back where it meets the other, a crease. Where the crease cannot be made cleanly, or on a round face both run along, the corner is rounded anyway.

When a Fillet Fails

If the fillet cannot be built, the page shows the reason beside it, and the value typed last turns red with the reason in its tooltip. Common fixes:

  • Reduce the Radius. A radius larger than the faces it rolls between cannot be built.
  • Turn on Overflow (under Options) where the fillet runs into a neighboring face.
  • Fillet fewer edges per feature, or fillet the larger radii first.

See Also