Skip to content

Component Patterns

Copies components along a direction, around an axis, or mirrors them across a plane. The copies follow their seed components.

Assembly tab > Linear Pattern, Circular Pattern or Mirror Components. The three share a split button, which shows the one used last; its arrow shows the others.

The Linear Component Pattern page beside an assembly with a row of patterned brackets.

Creating a Component Pattern

  1. Select the seed component in the design tree or the graphics area. You can also check seeds after the page opens.
  2. Click Linear Pattern, Circular Pattern or Mirror Components.
  3. Select a face for the direction, axis or plane, or click Front, Top or Right.
  4. Set the spacing and Instances (not for a mirror).
  5. Check the Components to Pattern.
  6. Click OK or press Enter. The status bar gives the number of instances created.

The page titles are Linear Component Pattern, Circular Component Pattern and Mirror Components. Only one pattern page, Mate or Motor page can be open at a time.

The copies are components of their own, fixed, and placed only by the pattern: when a seed moves, its copies move with it. They cannot be floated or dragged. Each copy uses the seed's part, configuration and appearance.

Direction, Axis or Mirror Plane

The section is Direction for a linear pattern, Axis for a circular pattern and Mirror Plane for a mirror. The box at its top names the reference in use, such as "Right Plane normal" or the component and face.

Front, Top, Right
Uses one of the assembly's origin planes: its normal for a direction or axis, the plane itself for a mirror.
Face

Select a face of a component in the graphics area while the page is open:

Pattern Takes
Linear A planar face (along its normal), or a cylindrical or conical face (along its axis)
Circular A cylindrical or conical face (its axis)
Mirror A planar face
Reverse direction
Patterns the other way along the direction, or the other way around the axis. Linear and circular only.

The defaults are the Right Plane for a linear pattern and a mirror, and the Top Plane for a circular pattern.

Spacing and Instances

Linear and circular patterns.

Spacing
Linear: the distance between neighboring instances, in the assembly's units. Default 50 mm (2 in).
Angle
Circular: the angle between neighboring instances, in degrees. Default 90°.
Instances
The number of instances, the seed included: a whole number from 2 to 500. Default 3 for a linear pattern, 4 for a circular one. With any other value, OK leaves the page open and the status bar says so.

A component pattern has one direction. It has no second direction and no instances to skip, unlike the part's Linear Pattern.

Copies

Mirror Components only. Each seed gets one copy.

Part symmetric about

The seed part's own plane it is symmetric about. The copy is the same part, mirrored in this plane and then in the mirror plane, so it is only turned. No opposite-hand part is created.

Option Plane
Automatic The plane the part's shape is most centered on
Its YZ plane The part's YZ plane
Its ZX plane The part's ZX plane
Its XY plane The part's XY plane

Use it for parts symmetric about one of their planes. A part that is not symmetric comes out as the same part turned, not its mirror image.

A bracket mirrored across the Right Plane with Mirror Components, the copy the same part turned.

Components to Pattern

Components
A check box for each of the assembly's own components that is not a pattern copy. The component selected when the page opened is checked. Components inside sub-assemblies cannot be seeds; pattern the sub-assembly instead.

In the Design Tree

Patterns are listed in the Patterns folder after the mates, named LocalLPattern1, LocalCirPattern1 or MirrorComponent1, with their seeds and their count and spacing ("3 × 50 mm", "4 × 90°" or "mirrored"). Each copy is listed with the components, marked "instance of" its pattern.

To change a pattern, double-click it, or right-click it > Edit Pattern…. The page is titled Edit and the pattern's name, such as Edit LocalLPattern1. Changing the count or the seeds adds or removes copies; removed copies take their mates with them.

Right-click a pattern for:

Command Result
Delete with Instances Deletes the pattern and its copies, with their mates
Delete and Keep Instances Deletes the pattern; the copies stay as fixed components

Components of a pattern, seeds or copies, cannot be formed into a sub-assembly or moved into one. Delete the pattern first.

See Also