Insert Fastener¶
Inserts library screws in holes from Hole features, each sized from its hole and long enough for the parts it clamps, with its nut and washers, mated in place. One click on a hole can fill its pattern, every hole of its Hole feature or every hole in the part, and the fasteners follow the holes when the parts change.
Assembly tab > Insert Fastener.

Inserting Fasteners¶
- Click Insert Fastener.
- Set Fill: what a hole you select fills. The default is its pattern instances.
- Select the cylindrical wall of a hole from a Hole feature, or its counterbore or countersink, in the graphics area. It is added to the Holes list, and the holes it fills are highlighted. Select more holes to add them.
- Set Held by and the washers. Under Sizes, select another thread or length for a group of holes if needed. The fasteners are shown in the graphics area as they will be added.
- Click OK or press Enter. The fasteners are added as one feature in the design tree, mated to their holes.
- Select the next holes, or click OK again with none selected, or click Close or press Esc.
Each OK is one step for Ctrl+Z. Finish any other open page, such as Mate or Motor, before starting.
Holes¶
Select the walls of holes that the Hole command sized from a clearance hole table, in the assembly's own parts. A screw goes in from the end of its hole with nothing in the way of its head. Selecting a counterbore or countersink selects its hole, and the head bears on the counterbore's floor. Selecting a hole in the list again takes it out.
- Fill
-
What each hole in the list fills. Changing it changes every hole in the list.
Option Fills Its pattern instances The hole and its copies in linear patterns, circular patterns and mirrors All holes of its Hole feature Every point of the hole's Hole feature, and their copies This hole only The hole alone All holes in the part Every hole from a Hole feature in the hole's part
The Holes list names each hole by its part, its Hole feature and what it fills, such as Plate<1>: Hole1, 6 pattern instances or Plate<1>: Hole1 point 2 in CirPattern1 instance 4. Instances are numbered as in SolidWorks: the seed is 1. Below the list, the page says how many holes will be filled, how many cannot be fastened and how many are skipped.
Right-click a hole in the graphics area, or select holes in the list and right-click, to:
- Fill its pattern instances, its feature's holes, this hole only or all holes in the part, for that hole alone.
- Remove from List.
- Skip This Hole: leave one of the holes it fills empty. Fill This Hole fills it again.
- Fill All Holes in Part
- Fills every hole from a Hole feature in the parts of the holes in the list.
- Fill All Holes in Assembly
- Fills every hole from a Hole feature in every part of the assembly, as SolidWorks' Populate All.
Holes that already have a screw are left out. A hole on the axis of a screw being added, such as the other plate's hole under a bolt, belongs to that screw's stack and gets no screw of its own.
A hole is refused, with the reason under Sizes, when:
- It was not made with the Hole command, or was not sized from a clearance hole table (Custom entry), or by a drill size.
- Its part is lightweight. Resolve it first. See Lightweight.
- Its part is inside a sub-assembly.
- Nothing is found around the hole for the screw's head to bear on.
The hole's Standard and Fastener set the fasteners:
| Hole Standard | Fastener | Screw | Nut | Washer |
|---|---|---|---|---|
| Metric clearance holes (ISO 273) | Socket head cap screw | ISO 4762 socket head cap screw; ISO 12474 for fine threads | ISO 4032 hex nut; ISO 8673 for fine threads | ISO 7089 plain washer |
| Metric clearance holes (ISO 273) | Flat head screw | ISO 7046-1 cross recessed countersunk flat head screw, M1.6 to M10 | ISO 4032 hex nut; ISO 8673 for fine threads | ISO 7089 plain washer |
| Metric clearance holes (ISO 273) | Countersunk socket head screw | ISO 10642 countersunk socket head screw | ISO 4032 hex nut; ISO 8673 for fine threads | ISO 7089 plain washer |
| Metric clearance holes (ISO 273) | Hex head screw | ISO 4017 hex head screw, threaded to the head; ISO 8676 for fine threads | ISO 4032 hex nut; ISO 8673 for fine threads | ISO 7089 plain washer |
| Metric clearance holes (ISO 273) | Hex head bolt | ISO 4014 hex head bolt, partly threaded; ISO 8765 for fine threads | ISO 4032 hex nut; ISO 8673 for fine threads | ISO 7089 plain washer |
| Metric clearance holes (ISO 273) | Button head screw | ISO 7380-1 button head socket screw | ISO 4032 hex nut; ISO 8673 for fine threads | ISO 7089 plain washer |
| Inch clearance holes (ASME B18.2.8) | Socket head cap screw | ASME B18.3 socket head cap screw, UNC and UNF | ASME B18.2.2 hex nut (machine screw nut to #12) | ASME B18.22.1 Type A narrow (SAE) |
| Inch clearance holes (ASME B18.2.8) | Flat head screw | ASME B18.6.3 cross recessed flat head machine screw, UNC and UNF | ASME B18.2.2 hex nut (machine screw nut to #12) | ASME B18.22.1 Type A narrow (SAE) |
| Inch clearance holes (ASME B18.2.8) | Countersunk socket head screw | ASME B18.3 flat countersunk head socket cap screw, UNC and UNF | ASME B18.2.2 hex nut (machine screw nut to #12) | ASME B18.22.1 Type A narrow (SAE) |
| Inch clearance holes (ASME B18.2.8) | Hex head cap screw | ASME B18.2.1 hex cap screw, UNC and UNF | ASME B18.2.2 hex nut | ASME B18.22.1 Type A narrow (SAE) |
| Inch clearance holes (ASME B18.2.8) | Button head screw | ASME B18.3 button head socket cap screw, UNC and UNF | ASME B18.2.2 hex nut (machine screw nut to #12) | ASME B18.22.1 Type A narrow (SAE) |
Only the sizes and lengths the company libraries offer are used.
A flat head screw's top is mated flush with the face around the countersink, and the clamped stack is measured from that face. Its length is overall, head included. No washer goes under a flat head. Each countersunk hole type has its own screws' countersinks, at least as wide as their heads' theoretical sharp diameter, so the head is flush: Flat head screw holes ISO 15065's (metric) or the ASME B18.6.3 head's (inch), Countersunk socket head screw holes ISO 10642's or the ASME B18.3 head's. A head wider than its countersink stands above the face, as the notes say.
Fastener¶
- Held by
-
What holds each screw at its far end:
Option The screw Auto (tapped part, else nut) Threads into a tapped part if one is found in the stack, else takes a nut. A tapped part when the standard has no nuts Nut Goes through, with a nut on the far side, even if a part in the stack is threaded Tapped part Threads into the tapped part in the stack; with none found, its length allows for one past the stack A tapped part is one with material inside the screw's thread diameter where the screw enters it.
- Screw
- The screw for holes sized by Screw clearance, which give a size but no screw: the screw types their clearance table has for the size (socket head cap screw, button head screw, hex head bolt…; not flat heads, which need a countersink). Auto is a hex head bolt (metric) or hex head cap screw (inch). Shown only when such holes are selected. Counterbored and countersunk holes, and holes sized for a screw, take their own.
- Washer under the nut
- Adds a washer between the far face and the nut. On by default. Used only with a nut.
- Washer under the head
- Adds a washer under the screw's head. Off by default. Not used with a flat head screw.
Sizes¶
The holes are grouped by size, then by the screw they take.
- Thread
- One for each size that comes in more than one thread, such as M8 thread. Auto takes a tapped part's thread, else the coarse one. The thread picked applies to every hole of that size.
- Lengths
- One list for each group of holes that take the same screw, such as M8x1.25: 6 holes, screws need 25.6 mm. Auto gives each hole the shortest length long enough for it. Select a length to give it to the whole group; shorter ones are marked (too short).
Below the sizes, notes report what to check, such as:
- No tapped part was found past the stack: the length allows for one there.
- The tapped part has less thread than the engagement needs.
- No screw offered is long enough.
- Why holes cannot be fastened.
Screw Length¶
The length under the head a screw needs is the clamped thickness, measured along the hole's axis through the parts that touch, plus:
| Held by | Added |
|---|---|
| Nut | The washers used, the nut's height and two thread pitches |
| Tapped part | The washer under the head, if used, and a thread engagement of 1.5 × the screw diameter |
The length is then rounded up to the next length the libraries offer.
What Is Added¶
The screw, washers and nut are embedded parts made from their library rows, each named by its standard and designation, such as ISO 4762 M8x30, as the Bill of Materials lists them. Each is mated Concentric with the hole and Coincident with the face it bears on, so it stays with the hole when the parts move.
Opening one from the assembly shows it read-only: it is its family's template part with its size's values.
A screw's thread is shown over its thread length from the tip, so you can see how far it is threaded. It is cosmetic (helix lines on the shank), or modeled when View > Threads > All Modeled is on. All Cosmetic and As Set in Each Thread show it cosmetic. Exports give it as a plain shank, unless Options > Files > Model threads on standard parts is on.

In the Design Tree¶
Each OK adds a fastener feature to the design tree, such as Fastener1. Open it to see its holes, each a folder named as the hole with its screw, washers and nut and a Mates folder with the mates that hold them.
- Double-click the feature to edit it: the page opens with its holes, options and sizes, and OK replaces what it added.
- Right-click it for Configure Children, Appearance of Children, Hide Children or Show Children, and Suppress Children or Unsuppress Children, each for all the parts it added at once. Configure Children sets the length of its screws.
- Delete with Its Parts removes the feature, its parts and its mates.
When the Parts Change¶
The fasteners follow their holes when a part is edited and saved, configured in the assembly, or rebuilt:
- Holes that are gone lose their fasteners.
- New holes that a hole in the list fills get fasteners, with the feature's options and sizes. Skipped holes stay empty.
- Holes whose stack changed, such as a plate made thicker, get the screw, nut and washers they need now. A length set with Configure Children is kept while it is still long enough.
The status bar says what changed, for example Fasteners updated to their holes: Fastener1 (2 added, 4 resized). The update is part of the change that edited the part, so Ctrl+Z undoes both.
Deleting a screw, washer or nut by itself removes the rest of its stack and leaves the hole skipped. To fill it again, edit the feature, right-click the hole and click Fill This Hole.