Skip to content

Sheet Format

A sheet format is a sheet's border, zones, title block and revision table, and the defaults it gives new drawings. One format fits every sheet size: the border keeps its margins from the paper's edge, and the title block's lines and text are measured from the border's lower right corner.

Right-click a sheet's tab below the graphics area, or its row in the design tree, > Edit Sheet Format, or Sheet Format tab > Edit Sheet Format.

img/drawings/sheet-format-editing.png

A sheet in Edit Sheet Format: the Sheet Format tab alone with Linework, Text, Settings, Save Format to Library and Done, and the title block's text boxes drawn dashed.

Editing a Sheet Format

  1. Show the sheet whose format to edit, and click Edit Sheet Format. The Sheet Format tab of the command panel is shown alone, with the format's commands, and each text item of the format is drawn in a dashed box.
  2. Draw or change the format's lines with Linework.
  3. Add text with Text, and drag, edit or delete the text items on the sheet.
  4. Set the margins, zones and revision table with Settings.
  5. Click Done.

The format is edited for every sheet of the drawing that uses it. If it is SpryCAD's or the company standards library's, editing it makes it a copy of the drawing's own, which no longer takes updates from Tools > Library Updates. If you click Done with the format as it was, it stays SpryCAD's or the library's. To share the edited format with other drawings, click Save Format to Library.

Each change is its own undo step: a linework session, a text placed or dragged, a text's page, the settings. There is no cancel for the whole edit; press Ctrl+Z to undo changes.

Format Commands

Command Does
Linework Sketches the format's lines. See Linework
Text Places a text item on the format. See Text
Settings Sets the format's name, margins, zones, revision table and defaults. See Format Settings
Save Format to Library Saves the format to the company standards library. See Save Format to Library
Done Closes the sheet format and returns to the drawing's tabs

Linework

Opens the format's lines in the sketcher, with every sketch tool, relation and dimension of a part's sketch. See Sketch.

  • The sketch's origin is the border's lower right corner, so the lines stay with it on every sheet size.
  • The rest of the sheet is drawn behind the sketch, to snap and dimension to.
  • Construction geometry is not drawn on the sheet.
  • Dimensions can use the sheet's size by name: SheetWidth, SheetHeight, BorderWidth and BorderHeight. A line dimensioned to BorderWidth, for example, spans the border on every size.
  • Each text item's box is four construction lines with a point at the middle of each side. Add relations and dimensions to its corners and midpoints to tie the text to the lines. Select a line of a box to edit its text on the sketch's page, with the same fields as the Format Text page.

Click Exit Sketch to keep the lines and the text changes as one undo step, or Discard Changes to leave them as they were. The Sheet Format tab is shown again.

Text

Places a text item where you click. Its box's lower left corner is at the point, sized to fit TEXT, and the Format Text page opens with the text selected to type over. Press Esc to end the tool without placing one.

To work with a text item on the sheet:

  • Click it to select it and open its page. Double-click opens it too.
  • Drag it to move its box. See Snapping.
  • Right-click it for Properties…, Fit Box to Text and Delete.
  • Select it and press Del to delete it with its box.

Format Text Page

Changes on the page show on the sheet as you make them. OK keeps them as one undo step. Cancel undoes them, and removes a text that was just placed.

img/drawings/sheet-format-text-page.png

The Format Text page for a title block value: Text with {PartNumber}, Property, Filled in by each drawing, the Format section and the Box section.

Text

Text
The text shown, on one line or several. A field in braces, such as {PartNumber} or {Sheet} / {SheetCount}, is filled in on each sheet. See Title Block for the fields. {ProjectionSymbol} alone draws the projection angle's symbol, Height high, in the middle of the box.
Property
Inserts a field at the cursor. The list holds the sheet's, the drawing's and the model's properties, the fields the format leaves to each drawing, and ProjectionSymbol.
Filled in by each drawing
Leaves the field to each drawing, which sets it in File > Properties…. Available when the text is one field alone, such as {Project}. See Title Block.

Format

Height
The capital height, in the drawing's units.
Horizontal
Where the text sits across its box: Left, Center or Right.
Vertical
Where the text sits up its box: Top, Middle or Bottom.
Bold
Draws the text bold.
Angle (°)
The text's angle, counterclockwise.

Box

Fit Box to Text
Makes the box the size the text needs, keeping its lower left corner, as far as its relations allow.
Snap gap
How far inside the title block's lines a dragged box snaps, in the drawing's units. Remembered for every drawing.

Snapping

A text box dragged on the sheet snaps, within 1.5 mm:

  • with its sides on the format's straight lines, or Snap gap inside them;
  • with its sides and middle in line with those of other text items.

Blue guides show what it snapped to. Snapping follows Tools > Options > Files > Snap annotations as they are dragged. A box tied to the lines by relations in Linework moves only as far as they allow.

Format Settings

Sets the format's name, border, zones, revision table and the defaults it gives new drawings. The sheet shows each change as you make it.

Sheet Format tab > Settings, while editing the sheet format.

img/drawings/sheet-format-settings.png

The Format Settings dialog: Name, Margins, Zone size, the revision table and projection options, Units and Properties each drawing fills in.

Name
The format's name, shown in Sheet Properties and offered as the name in Save Format to Library. Required.
Margins
The border's distance from the paper's edge at the left, right, top and bottom, in the drawing's units.
Zone size
The approximate spacing of the zone marks along the border, in the drawing's units. 0 draws no zones.
Zones from lower right (ASME)
Numbers the zones from the right and letters them from the bottom, as ASME does. Off, they are numbered from the left and lettered from the top, as ISO does. A new drawing on the format is set to the matching drafting standard, unless its template sets one.
Revision table
Draws the revision table, hanging from the border's upper right corner: a row for each release of the drawing, oldest first. See Revisions.
Third angle projection for new drawings
The projection angle of a new drawing's first sheet. Off, first angle. Sheets added to a drawing take the current sheet's angle instead. See Projection Angle.
Number revisions (01, 02) instead of letters
Names the drawing's releases 01, 02 and so on instead of A, B and so on, when its first sheet uses the format.
Units
MMGS or IPS: the units of new drawings on the format, and of a drawing whose first sheet uses it.
Properties each drawing fills in
The fields left to each drawing, separated by commas, such as Company, DrawnBy. Each has a row in File > Properties…. See Title Block.

Click OK to apply the changes to every sheet that uses the format, as one undo step. Cancel leaves the format as it was.

Save Format to Library

Saves the sheet's format to the company standards library, for every drawing to choose in Sheet Properties and when creating a drawing.

Sheet Format tab > Save Format to Library, while editing the format or not.

  1. Click Save Format to Library.
  2. Type the format's name in the library. The format's own name is suggested.
  3. Click OK. If the library has a format of that name, a dialog asks to Replace it.

The format is published as a new revision of the library. The drawing then uses the library's format, so later changes to it reach the drawing through Tools > Library Updates.

A company standards library must be published first, from Tools > Libraries > Edit Standards Library. While SpryCAD's default standards are in use, the command says so and saves nothing.

Save as Template

Saves a drawing template to the company standards library. A template is what a new drawing starts from: it is offered under Template when creating a drawing or making one from a part or assembly.

Sheet Format tab > Save as Template.

The template keeps:

  • the current sheet's format, by reference to SpryCAD's or the library's format;
  • the current sheet's size;
  • the drawing's drafting standard;
  • the title block values filled in, from File > Properties…. Empty values are left out.

To save one:

  1. Set the sheet's format and size in Sheet Properties, the Drafting Standard, and the title block values. See Title Block.
  2. Click Save as Template.
  3. Type the template's name. The format's name and the sheet size are suggested, such as ISO A3.
  4. Click OK. If the library has a template of that name, a dialog asks to Replace it.

The template's format must be SpryCAD's or the library's, unchanged:

  • A format edited in the drawing is the drawing's own. Save it with Save Format to Library first.
  • A format that differs from the library's current one must be updated first, with Tools > Library Updates.

A company standards library must be published first, from Tools > Libraries > Edit Standards Library.

Template also lists SpryCAD's ISO and ANSI formats, and each library format that no template uses, on no size of their own.

Built-in Formats

SpryCAD comes with two formats. A new drawing in millimeters starts on ISO, one in inches on ANSI.

Setting ISO ANSI
Title block ISO 7200 ASME Y14.1
Projection angle First angle Third angle
Units MMGS IPS
Margins 20 mm left, 10 mm right, top and bottom 0.5 in on every side
Zones About 50 mm apart, from the upper left About 50 mm apart, from the lower right
Labels Mixed case: Drawing number, Checked by Capitals: DWG NO., CHECKED

Both have the same 180 × 36 mm title block and a revision table with Rev., Description, Date and Approved columns. The title block's boxes, from the bottom row up:

Row Boxes
1 Title ({Description}), Drawing number ({PartNumber}), Rev. ({Revision})
2 Material, Finish, Scale, Sheet ({Sheet} / {SheetCount}), Units
3 Drawn by, Date, Checked by, Version, and Projection (the projection symbol, two rows high)
4 Company, Approved by

Company, Drawn by, Checked by and Approved by are filled in by each drawing. See Title Block.

See Also